Installation

If you have problems applying our stickers, here are some tutorials to learn how to do it

Choose a product: Honda Africa Twin CRF 1100 , BMW R 1200 GS/GSA LC swingarm sticker , BMW R 1200 GS , BMW S1000XR decal , BMW S1000XR TankPad , Car Rear Bumper protector , Rim Sticker , Yamaha MT09 Tracer , Yamaha Ténéré 700 , Yamaha TMAX 530

HONDA AFRICA TWIN CRF 1100

BMW R 1200 GS/GSA LC swingarm sticker

Remember to apply the adhesive in a place with good temperature (between 25ºC and -15ºC).
We recommend that you do not use the motorcycle until 48 hours have passed since the installation of the stickers, so that the glue can act to its full capacity.

The installation consists of:

1. Start by cleaning the surface where you are going to apply the adhesive with alcohol only. Avoid industrial cleaners that can damage the paint on the bike or the adhesive glue.

2. Pre-adjust the adhesive without sticking it to ensure you install it correctly.

3. Peel off the adhesive backing from one end.

4. Apply the part without silicone paper. Now continue applying the rest of the piece while removing the rest of the silicone paper. Remember to do it in the same direction so that no air gets trapped under the adhesive, which could cause bubbles.

BMW R 1200 GS

BMW S 1000 XR Graphics

BMW S 1000 XR Tank Pad

Car Rear Bumper Protector

This product has the front flap of the packaging designed to be used as a sustainable squeegee .

Remember to apply the sticker in a good tempered place (between 25ºC and -15ºC).

We recommend not to put anything onto the sticker until 48h-72h have passed from the stickers installation, so the glue acts at its full capacity.

The installation consists of:

1. Start cleaning the surface where you are going to apply the sticker with only alcohol. Avoid industrial cleaners that can damage the motorcycle paint or the glue in the sticker.

2. Remove the central part of the adhesive backing and stick it at the center of the bumper.

3. Start sticking one side while removing the backing and applying pressure with the squeegee to remove the air.

4. Do the same on the other side of the sticker.

Rim Sticker

Remember to apply the sticker in a good tempered place (between 25ºC and -15ºC).
We recommend not to use the motorcycle until 48h have passed from the stickers installation, so the glue acts at its full capacity.

The installation consists of:

1. Start cleaning the surface where you are going to apply the sticker with only alcohol. Avoid industrial cleaners that can damage the motorcycle paint or the glue in the sticker.

2. Choose which part of the rim you want to decorate first. Preset the sticker without hooking it to make sure you install it the correct way.

3. Peel off the adhesive backing.

4. Apply the piece in the same direction so no air gets stuck under the sticker making bubbles.

Yamaha MT09 Tracer

Remember to apply the sticker in a good tempered place (between 25ºC and -15ºC).
We recommend not to use the motorcycle until 48h have passed from the stickers installation, so the glue acts at its full capacity.

The installation consists of:

1. Start cleaning the surface where you are going to apply the sticker with only alcohol. Avoid industrial cleaners that can damage the motorcycle paint or the glue in the sticker.

2. Peel off the adhesive backing on one end.

3. Preset the sticker without hooking it to make sure you install it the correct way.

4. Apply the part with no silicone paper. Now keep applying the rest of the piece while removing the rest of the silicone paper. Remember to do it in the same direction so no air gets stuck under the sticker making bubbles.

Yamaha Tenere 700

Remember to apply the sticker in a good tempered place (between 25ºC and -15ºC).
We recommend not to use the motorcycle until 48h have passed from the stickers installation, so the glue acts at its full capacity.

The installation consists of:

1. Start cleaning the surface where you are going to apply the sticker with only alcohol. Avoid industrial cleaners that can damage the motorcycle paint or the glue in the sticker.

2. Peel off the adhesive backing on one end.

3. Preset the sticker without hooking it to make sure you install it the correct way.

4. Apply the part with no silicone paper. Now keep applying the rest of the piece while removing the rest of the silicone paper. Remember to do it in the same direction so no air gets stuck under the sticker making bubbles.

Yamaha TMAX 530

Remember to apply the sticker in a good tempered place (between 25ºC and -15ºC).
We recommend not to use the motorcycle until 48h have passed from the stickers installation, so the glue acts at its full capacity.

The installation consists of:

1. Start cleaning the surface where you are going to apply the sticker with only alcohol. Avoid industrial cleaners that can damage the motorcycle paint or the glue in the sticker.

2. Peel off the adhesive backing on one end.

3. Preset the sticker without hooking it to make sure you install it the correct way.

4. Apply the part with no silicone paper. Now keep applying the rest of the piece while removing the rest of the silicone paper. Remember to do it in the same direction so no air gets stuck under the sticker making bubbles.